Minka Lavery 1011-44-PL Guide d'installation

Naviguer en ligne ou télécharger Guide d'installation pour Supports de plafond pour panneaux plats Minka Lavery 1011-44-PL. Minka Lavery 1011-44-PL Installation Guide Manuel d'utilisatio

  • Télécharger
  • Ajouter à mon manuel
  • Imprimer
  • Page
    / 1
  • Table des matières
  • MARQUE LIVRES
  • Noté. / 5. Basé sur avis des utilisateurs
Vue de la page 0
INSTALLATION INSTRUCTIONS
For Model #1011-44-PL
WARNING! SHUT POWER OFF AT FUSE OR CIRCUIT BREAKER.
CAUTION
Turn off the main power at the circuit breaker before installing
the fixture, in order to prevent possible shock.
GENERAL
All electrical connections must be in accordance with local
and national electrical code (N.E.C) standards. If you are
unfamiliar with proper electrical wiring connections obtain the
services of a qualified electrician.
Remove the fixture and the mounting package from the box
and make sure that no parts are missing by referencing the
illustrations on the installation instruction.
ASSEMBLY AND INSTALLATION
1. Take the fixture out of the box. Remove the Acrylic
Lens(20) from the fixture and place aside on a flat
surface to avoid damage to the lens. To remove the lens,
pull one end cap outward and then remove the acrylic
lens from the fixture.(Refer to process #1). Then take the
cardboard out from the End Cap.
2. Pull the Supply Wires (3) & (4)and House Ground
Wire(2)out from the Outlet Box(1).
3. Install the Canopy(11) to the Outlet Box(1)by using two
Mounting Screws(13). (Note: The side of the Canopy
marked "GND" must face out.)
4. Position your fixture over the Outlet Box(1).Mark the
location of the four Keyhole Slots(15)located on the
Fixture Body(14). Be sure to mark only the narrow part of
the Keyhole Slots(15).Remove the Fixture Body(14) from
the ceiling. Drill the four Holes(5) using the appropriately
sized drill bit. Insert the provided Ceiling Anchors(6) into
the holes.
5. Make the wiring connections: connect the House Ground
Wire(2)to the Fixture Ground Wire (9) using Wire
Connector (7) ; connect the White Supply Wire(3)to the
White Fixture Wire(8); connect Black Supply Wire(4)to
the Black Fixture Wire (10) using Wire Connectors (7).
Carefully tuck all wires back into the Outlet Box(1).(See
Fig.2)
6. Attach the Fixture Body(14) to the Canopy(11) through
the 2 Downward Screws(12) and tight it with 2 Nuts(18).
7. Feed the four Anchor Screws(17) through the narrow part
of the Keyhole Slots(15).Tighten the Anchor Screws (17)
into the Ceiling Anchors (6) until the Fixture Body (14) is
flush with the ceiling.
8. Install the Fluorescent Tube(19) into the Sockets(16).
Please follow the wattage label located on the fixture
body. Do not exceed the recommend wattage.
9. To install the Acrylic Lens(20),carefully slide the lens to
the end cap which is fixed, making sure the lens is way to
the end of the End Cap. Pull the other end cap which is
moveable outward and put the Acrylic lens(20) down.
Then the Acrylic Lens(20) will be hold by the end
cap.(Refer to process#2)
INSTALLATION IS NOW COMPLETED
Fig.1
Fig. 2
FIXTURE
WIRES
Black or
Smooth
HOUSE
WIRES
Black
(Hot)
FIXTURE
WIRES
White or
Ribbed
HOUSE
WIRES
White
(Neutral)
FIXTURE
WIRES
Bare
Copper
(Ground)
HOUSE
WIRES
Green
(Ground)
Process.2
Process.1
PDF created with pdfFactory Pro trial version www.pdffactory.com
Vue de la page 0
1

Résumé du contenu

Page 1 - INSTALLATION INSTRUCTIONS

INSTALLATION INSTRUCTIONS For Model #1011-44-PL WARNING! SHUT POWER OFF AT FUSE OR CIRCUIT BREAKER. CAUTION Turn off the main power at the circuit br

Commentaires sur ces manuels

Pas de commentaire