Minka Lavery 1546-77 Manuel d'instructions

Naviguer en ligne ou télécharger Manuel d'instructions pour Non Minka Lavery 1546-77. Minka Lavery 1546-77 Instructions / Assembly Manuel d'utilisatio

  • Télécharger
  • Ajouter à mon manuel
  • Imprimer
  • Page
    / 1
  • Table des matières
  • MARQUE LIVRES
  • Noté. / 5. Basé sur avis des utilisateurs
Vue de la page 0
INSTALLATION INSTRUCTIONS
Item#1546 (Rev. 08/29/2013)
READ AND SAVE THESE INSTRUCTIONS
WAR N I N G ! S H U T P O W E R O F F AT F U S E O R CI R C U I T B R E AK E R .
AVERTISSEMENT! COUPER LE COURANT AU NIVEAU DES FUSIBLES OU DU DISJONCTEUR.
Fig. 1
Fig. 2
LA-1831E
HANGING THE FIXTURE (Fig. 1)
1. Shut off the power at the fuse box or circuit
breaker. If necessary, remove the old fixture
including the mounting hardware.
2. Carefully remove the fixture from the carton and
check that all parts are included as shown in the
illustration.
3. Attach the crossbar (A) to the outlet box using
mounting screws (B) (Size: #8-32N*L0.5”). The
side of the crossbar marked “GND” must face out.
4. Thread the nipple (D) part way into the center hole
of the crossbar (A).
5. Determine the desired hanging height and thread
rods (F) to metal frame (H). Carefully pass the
wires through each rod as you assemble. Then
attach the loop (G) to the top of rods (F).
6. By measuring, determine correct number of links
needed for proper hanging height. Using a pair of
chain pliers, disconnect and discard remaining
chain, then attach the chain to loop (G) and the
loop on canopy (C). Carefully lace the fixture wires
through the chain, loop (G) and the loop on
canopy (C).
CONNECTING THE WIRES (Fig. 2)
7. At this point, connect the electrical wire as shown
in figure 2, making sure that all wire connectors
are secured. If your outlet box has a ground wire
(green or bare copper), connect the fixtures
ground wire to it. Otherwise, connect the fixture’s
ground wire directly to the crossbar using the
green screw provided. After the wires are
connected, tuck them carefully inside the outlet
box.
FINISHING THE INSTALLATION (Fig. 1)
8. Place the canopy (C) over the nipple (D), and
secure the canopy (C) against the ceiling using
knurled cap (E).
9. Place the glass shades (J) and metal rings (L)
over the sockets and secure with socket rings (I)
by using spanner (K) provided.
10. Install light bulb(s) (not included) in accordance
with the fixture’s specifications. (DO NOT
EXCEED THE MAXIMUM WATTAGE RATING!)
(NE PAS DEPASSER LA PUISSANCE
NOMINALE MAXIMALE!)
Your installation is now complete. Return power to
the outlet box and test the fixture.
Note: Illustration (Fig. 1) on this manual is for
installation purposes only. It may or may not be
identical to the fixture purchased.
FIXTURE
WIRES
Black or
Smooth
HOUSE
WIRES
Black
(Hot)
FIXTURE
WIRES
White or
Ribbed
HOUSE
WIRES
White
(Neutral)
FIXTURE
WIRES
Bare
Copper
(Ground)
HOUSE
WIRES
Green
(Ground)
H
A
B
D
E
K
I
F
F
G
C
Outlet Box
(Ceiling)
L
J
Set# A-010
- Crossbar
- Ground screw
- Mounting Screw*2
Rod# W30-1*6(F)
W30-H*2(F)
Socket Ring # SKT-RING-26
Spanner # WRH-T1-51
Vue de la page 0
1

Résumé du contenu

Page 1 - INSTALLATION INSTRUCTIONS

INSTALLATION INSTRUCTIONSItem#1546 (Rev. 08/29/2013)READ AND SAVE THESE INSTRUCTIONS WAR N I N G ! S H U T P O W E R O F F AT F U S E O

Commentaires sur ces manuels

Pas de commentaire